Video from my YouTube channel

Subscribe to My You tube channel

Vebe test for concrete

By -
Vebe test is a laboratory test used to determine the consistency of concrete. Vebe time is the time required to transfer concrete from frustum cone into a cylindrical shape using vibration and compaction. the Vebe time will increase with decreasing concrete workability.










Limitation
Vebe test is not suitable for concrete with maximum size aggregate greater than 63 mm. also if the value of Vebe time is less than 5 seconds and more than 30 seconds.


Apparatus 

  • Vebe consistometer 
  • Tamping rod
  • stopwatch 
  • Trowel 


Procedure

  1. Perform the slump test inside the container.
  2. place the transparent plastic disk above the concrete in the container.
  3.  switch the vibration on and start the stopwatch simultaneously.
  4. record the time required to change the concrete from a conical shape to cylindrical shape. You need carefully to observe the plastic disk on top of concrete.once the concrete transferred to the cylindrical shape and covered the plastic disk completely record the time from stopwatch.





Comments

  1. JBS Concrete NycDecember 2, 2019 at 3:52 AM

    Nice reading, I love your content. This is really a fantastic and informative post. Keep it up and if you are looking for nyc sidewalk concrete violation then visit JBS Concrete Nyc.

    ReplyDelete

Post a Comment

Videos from My Youtube channel

Popular posts from this blog

Pile cap

By -
Image
Pile cap used to transfer the loads from superstructure to the piling. The pile cap is thick concrete mat rests on piles. It is part of the foundation and used to distribute the loads over the piles. Piles used when the soil bearing is not enough to carry loads of the structure. Figure 1  construction management: concrete construction bridge construction:How to become a bridge engineer Pile cap construction procedure Excavation around piles: After 7 days of the casting of the pile the concrete will gain approximately, 70% of it is compressive strength. The soil around piles will be removed to the required levels and dimension that allows construction of the pile cap. A step shall be made if the excavation is more than 1.5 m to prevent soil collapse. Figure 2 Pile head cutting: Concrete will be removed up to cut off level. If concrete under the cut off level is unsound. It shall be removed, and the pile will be repaired...
Read more

Repairing of concrete bulging

By -
Image
Improper designing and installation of formwork for a concrete member can result in concrete Bulging. During the placing and compacting of concrete, forms may deflect largely in the weak areas. The deflection of forms will cause concrete to expand at this location, and this known as concrete Bulging. Concrete Bulging will spoil the appearance of a concrete member. Therefore we should always ensure that the forms are appropriately installed, and it is sufficiently supported to resist the concrete during placing and compacting. Bulging should be repaired in case we couldn't avoid it. The solution of concrete Bulging, offset, or surface irregularities are surface grinding. However, excessive surface grinding can weaken the concrete.  Figure 1 If the bulging or surface irregularities are small, grinding of concrete surface will be sufficient to remove surface irregularities. If the Bulging of concrete is significant, then the concrete should be chipped, and the surface...
Read more

prestressing equipment

By -
Image
Jacks are essential tools in prestressing operations and are used to apply tension to strands within tendons. There are two main types of jacks: A. Mono-Strand Jack A mono-strand jack is primarily used in building construction, where tendons typically consist of a small number of strands (usually 3 to 4). This type of jack is designed to stress each strand individually, ensuring precise control over the tensioning process. Since buildings generally have shorter tendons compared to bridges, stressing strands one by one is a practical and efficient approach in this context. construction management: concrete construction bridge construction:How to become a bridge engineer B. Multi strands jack:  In bridge construction, where tendons contain a significantly larger number of strands, using a mono-strand jack would be impractical. Stressing strands one by one in such cases would not only be time-consuming but also increase the risk of strand entrapment. Ther...
Read more

Bridge Diaphragm

By -
Image
The main function of diaphragms is to provide a stiffening effect to deck slab in case bridge webs are not situated directly on top of bearings. Therefore, diaphragms may not be necessary in case bridge bearings are placed directly under the webs because loads in bridge decks can be directly transferred to the bearings.On the other hand, diaphragms also help to improve the load-sharing characteristics of bridges. Diaphragms also contribute to the provision of torsional restraint to the bridge deck. Diaphragm will be used also to resist stresses that occurs during the post-tensioning process. Post-tensioning hardware are casted inside the diaphragm. Figure 1 construction management: concrete construction bridge construction:How to become a bridge engineer Types of diaphragm: Diaphragm at the span end: this type of diaphragms will be located between two bridge spans or at the bridge abutments. Expansion joints will be used to connect bridge spans. This ...
Read more

Driven piles

By -
Image
Driven piles have been used widely as a foundation for different structures. In this type of foundation. Piles are driven to soil mechanically using a hammer. There are enormous types of driven piles. construction management: concrete construction bridge construction:How to become a bridge engineer  Steel H Piles Section of H-pile consists of flange and web, as shown in figure no:1. They are driven using a high impact hammer, and the likelihood of pile damage is low. H-piles resists the loads through skin friction or end bearing or both. Since the displacement of soil is minimal, this type of piles can be driven into dense granular soil or stiff clay layers. Although some problem during driving may arise. Plugging is one of them. After driving the pile to a certain level. soils will adhere to pile web and between the flange creating a closed end. This will change the pile to displaced pile and complicate pile driving. H-piles should be protect...
Read more

Flakiness Index and Elongation Index of Coarse Aggregates

By -
Image
Flaky and elongated aggregates can adversely affect concrete. Flaky and elongated aggregates are difficult to compact. Therefore using flaky and elongated aggregates will reduce concrete workability, which required more amount of water to produce a workable mix. Increasing water content will reduce concrete strength and durability. Moreover, these aggregates are not robust, which leads to lowering concrete strength. Figure 1 construction management: concrete construction bridge construction:How to become a bridge engineer The Flakiness Index of aggregates is the percentage by weight of particles whose least dimension (thickness) is less than three- fifths (0.6times) of their mean dimension. This test does not apply to sizes smaller than 6.3mm. The Elongation index of an aggregate is the percentage by weight of particles whose greatest dimension (length) is greater than nine-fifths (1.8times) their mean dimension. Flakiness and elongation tests ar...
Read more

Binding wire for steel reinforcement

By -
Image
  Binding wires are used to tie steel bars together. These wires are playing a significant role in maintaining the reinforcement stability and rigidity. Wires are used to tie the steel bars at intersections points. By tying the steel bars together, we ensure that the steel bars will not move from their locations during construction or during the time of concreting. In slabs, binding wires are used to tie longitudinal and transverse bars together. In columns, it is used to tie vertical bars with stirrups.   Figure 1 There are various types of binding wires such as  Black annealed baling wire, Stainless Steel Binding Wire, and PVC coated binding wires.  Black annealed baling wire used to tie black steel. The popular size for black wire ranges from 16 to 22 gauges. Stainless steel binding wires are used to bind stainless steel reinforcement. Stainless steel reinforcement is used in a harsh environment where the black steel gets rusted quickly. Therefore, stainless ...
Read more

Chamfers for concrete structures

By -
Image
In general, the edges of concrete members are chamfered. Usually during the process of installing forms for a structural member such as pile cap, a chamfer a PVC chamfer as shown in figure no:1 installed at the edges of the structural members. These chamfers will form smooth slanted edges, as shown in figure no:2. The size of chamfers can be 20x20mm or more as shown on the contract drawing. The PVC chamfer fixed to forms by nails. We should ensure that the PVC chamfer fixed in their correct locations, and we should ensure that the PVC chamfer is straight and not moving up or down. Checking the alignment and location of PVC chamfer is important, so the chamfered concrete edge will have a good appearance after the form’s removal.  Figure 1 Figure 2 Chamfering the concrete edges done for many reasons such as aesthetics, some suggesting that the chamfering of concrete edges done for safety to reduce the damage of objects due to impact with sharp concrete edges. Actually, ...
Read more

Casing for piles

By -
Image
The casing is a thick steel tube. The casing used extensively in construction drilled piles. The casing used to guide the drilling rig to drill the pile hole in the correct location. Also, it can be used to stabilize and prevent the soil from collapse until the concreting of the pile is completed. Furthermore, the casing will be used to hang the steel cage until the concrete is poured. The used casing should be thick and strong enough to resist the imposed stresses during the installation and removal process for temporarily casing. The casing should be clean, smooth, free from encrusted concrete, or any damage that can affect the size and shape of the pile. Figure 1 The casing length will vary according to the purpose of use and the type of the soil. If supporting fluids are used to stabilize the soil, the casing will be used as a guide for the drilling rig. Therefore, the casing length will be short. If the casing is used to support the soil, the casing length should be s...
Read more

Tunnel lining systems-Ribbed system

By -
Image
Ribbed supporting system has been used for many years to support tunnels. The ribbed supporting system is based on steel ribs supporting tunnels. The implementation of this system involves the installation of rolled steel sections around the circumference at specified spaces. The formation of gaps between the steel ribs and the ground is very common. These gaps should be suitably wedged to avoid excessive deformation of the ground. It is essential to ensure that the loads are distributed evenly by the steel support around the tunnel profile. Subjecting of steel support to point load will significantly reduce their ultimate capacity.  Figure 1 The steel ribs can be combined with shotcrete concrete. The shotcrete concrete will be applied before the erecting of ribs. The applying of a layer of shotcrete concrete will reduce the problems of gaps between ribs and surrounding ground, which minimize the wedging problems. Then another layer of shotcrete can be applied afte...
Read more